Many debriefs of navigation, cargo and mooring incidents finish with the same four questions. This lesson works through them in an original form, for use in ship's training meetings, assessor workshops and self-study. It does not replace your company's safety management system (SMS), risk assessments or the vessel's own procedures.
Discussion question 1 — How can we avoid such situations?
Most serious incidents do not come from one big mistake. They come from small gaps that add up: a passage plan nobody checked closely, a cargo plan changed and not re-briefed, or a mooring team that is tired and short of people. Prevention usually means:
- Plan, then brief. Explain the plan to the people who will carry it out, and say clearly what would make you stop.
- Check what changed. Changes in weather, berth, cargo order, pilot advice or crew are when old assumptions stop being true.
- Use stop-work authority. Anyone should be able to call a pause without being blamed for it.
- Close the loop on lessons. Near-misses and safety alerts count only when they change a checklist, a briefing or a drill.
Discussion question 2 — Key hazards and risks
| Operation | Typical hazards | Typical consequences |
|---|---|---|
| Navigation | Poor passage planning, over-reliance on ECDIS/automation, unclear bridge team roles, pilot–master misunderstanding, fatigue, restricted visibility | Grounding, collision, allision |
| Cargo work | Changed stowage or sequence, stability and stress margins, lifting over people, enclosed spaces, toxic or flammable atmospheres, cargo shift | Injury or death, structural damage, pollution, fire |
| Mooring | Snap-back zones, worn or mixed lines, poorly maintained winches and brakes, too few people, poor communication with the bridge, passing-ship and wind loads | Line parting, crush injuries, breakaway |
Mooring deserves special attention. Line-of-fire injuries happen fast and are often fatal. A painted snap-back zone is no guarantee of safety, because a parting line can whip outside the marked area.
Discussion question 3 — Controls and processes we have
Use the hierarchy of controls. Start at the top and use the weakest controls (procedures and PPE) only as the last layer, never on their own.
- Eliminate or substitute: remove the person from the hazard, for example by changing the mooring arrangement or the lift path.
- Engineering: maintained brakes and tested brake-holding capacity, line management plans, alarms, guards.
- Administrative: SMS procedures, risk assessments, permits to work, toolbox talks, the passage plan, the cargo plan, bridge resource management (BRM).
- People and PPE: competence, manning and rest hours, protective equipment.
Ask what these controls look like on your own ship. Who signs them off, and when were they last tested?
Discussion question 4 — The assessor's role
An assessor or mentor reduces risk by:
- Assessing competence, not paperwork: watch the task being done and ask "what if" questions.
- Spotting drift: notice where everyday practice has moved away from the written procedure, and report it without blame.
- Coaching: explain why each control exists, so people keep using it when nobody is watching.
- Feeding back: pass findings to the master, the DPA or the training department so procedures stay up to date.
Control of Work: the Performing Authority
Permits to work only control risk when the person running the job on the worksite understands them. Offshore, that person is usually called the Performing Authority (PA). The PA leads the work party and accepts the permit from the Area Authority, who issues it.
OPITO's Control of Work Training for Performing Authorities covers this role. According to OPITO's course overview it involves:
- 7 guided learning hours and a certificate valid for 2 years, with a refresher course to renew it;
- four mandatory units:
- Legal responsibilities: the PA's legal duties when overseeing a work party.
- Hazard recognition and risk control: formal risk assessments and safe systems of work.
- Monitoring and control: adapting the job when conditions or plans change.
- Communication and handover: clear briefings and handovers at every stage, including shift changes.
- key learning areas of risk assessment, issuing and managing work permits, safety-critical equipment, and emergency or incident response.
This links directly to discussion question 3: the permit is an administrative control. It protects people only while the PA keeps checking that the conditions written on it are still true. If something changes, stop, re-assess and re-issue the permit rather than carrying on. Your installation's or vessel's own Control of Work procedure decides the roles and signatures.
Becoming a formally trained competence assessor
Offshore employers often appoint assessors through a recognised scheme. One example is OPITO's Competence Assessor Training standard. According to OPITO's course overview it:
- is meant for people appointed to carry out competence assessments in their organisation, such as supervisors, managers and team leaders;
- involves about 14 guided learning hours across three mandatory units, covering the principles and roles of assessment, planning and carrying out assessments, judging evidence objectively, keeping records, checking (verifying) assessment records, and giving feedback;
- requires workplace evidence of assessing at least two candidates before the OPITO Competence Assessor Certificate is awarded.
The points above follow directly from the four discussion questions. An assessor's judgement is only as good as the evidence, the records and the feedback behind it. Always check the current requirements with OPITO or an approved training centre (opito.com). Your company's competence management system decides who may assess what.
Self-test
- Why does a briefing matter as much as the plan itself?
Answer 1
A plan only protects people who understand it. The briefing shares the intent, each person's role and the stop criteria.
- Is the painted snap-back zone a fully safe boundary?
Answer 2
No. A parting line can recoil outside the marked area. Keep people out of the line of fire wherever you can.
- Where do procedures and PPE sit in the hierarchy of controls?
Answer 3
At the bottom. They are the last layers, used after elimination, substitution and engineering controls.
- What is an assessor's main contribution beyond signing records?
Answer 4
Seeing real competence and practice drift, coaching the reasons behind controls, and feeding findings back into the SMS.
- Under OPITO's Competence Assessor Training, what must a learner provide besides completing the course units?
Answer 5
Workplace evidence of assessing at least two candidates. Only then is the certificate awarded.
References
- IMO, International Safety Management (ISM) Code.
- The Nautical Institute, The Navigator and Mariners' Alerting and Reporting Scheme (MARS).
- OCIMF, Mooring Equipment Guidelines (MEG4).