Entering a lock is precision ship handling at very low speed, with only a few metres of water on each side. This lesson explains the technique for three situations: a reasonably wide lock, a very narrow lock, and a river lock with a current. It is general training material. The lock authority's rules, the pilot's advice and your company's procedures always come first.
1. Keep watching your position and heading
- Watch the vessel's position and heading against the lock the whole time, not just at the entrance.
- The best place to judge alignment is the bridge wing. Look along the lock wall, or along your own ship's side, as a sighting line.
- If you know the lock width and your ship's beam, the clearance you can see on one side tells you the clearance on the other: far-side clearance ≈ lock width − beam − near-side clearance. Get the real figures from the lock's published data and your ship's particulars.
- If the wind is pushing the ship sideways, work back to the right track without changing heading where you can. A heading change near the entrance quickly turns into the bow or stern touching the wall.
2. Why speed must be as low as possible
Going astern makes the ship swing. Sooner or later you have to stop inside the lock. On a single fixed-pitch propeller, going astern makes the stern walk sideways (the propeller transverse thrust effect, also called prop walk), so the ship starts to swing. The more speed you carry in, the more astern power you need, so the faster you swing and the harder you hit the wall.
Water has to get out past the hull. As the ship enters, the water in the lock chamber has to flow out through the narrow gap between the hull and the walls. The faster the ship goes, the faster that flow.
If you are off the centreline, the ship gets pulled sideways. The flow on the narrower side is faster, and faster water means lower pressure (Bernoulli's principle). The ship is drawn sideways towards the nearer wall, often just as the bow enters, and there may be no time to correct it. This is closely related to bank effect and squat in shallow, confined water.
So: enter at the lowest speed that still lets you steer.
3. A reasonably wide lock (bow thruster or bow tug available)
- Approach at dead slow, lined up with the lock axis, and confirm your clearances from the bridge wing.
- Use short kicks ahead on the engine to keep just enough water over the rudder to steer. In strong wind, take tugs.
- If the rudder stops having effect at very low speed, correct heading with short bursts of bow thruster. The bow keeps swinging for a while after the thruster is stopped, so stop it early.
- Allowing for the lock length and the space available, start stopping early. When you go astern, be ready to counter the prop-walk swing with the bow thruster at the same moment. Otherwise the ship drifts off heading and the stern quarter lands on the wall.
- Make sure the forecastle team does not make the forward spring fast while the ship is still moving ahead. A spring held too early swings the bow towards the side where the spring is held. If that happens, push the bow off with the bow thruster.
- Hold the ship alongside on her lines, or on the forward spring, with the engine going ahead slowly and the rudder hard over. Use the bow thruster to keep the bow pressed in as needed.
4. A very narrow lock
- Go in at minimum speed. Control heading with engine kicks and the bow thruster.
- Approach the lead-in (approach) wall at a small angle, as if you were berthing alongside it.
- Reduce that angle gradually and settle gently alongside the lead-in wall. Go astern if needed to get down to minimum speed, and keep watching the sideways drift as the ship slows.
- Using bow thruster and engine, keep pressed against the lead-in wall and creep along it into the lock. Do not let the bow come away from the lead-in wall, or the bow shoulder may strike the far corner of the entrance.
- Pass the forward spring. Again, do not let the forecastle team make it fast while the ship is still moving ahead.
5. A river lock with current
- Approach at the lowest safe speed and get ready to turn towards the lock early.
- Turning usually needs engine ahead, rudder hard over and the bow thruster helping the turn. The turn takes time, and the current keeps carrying you the whole time, often towards the upstream or downstream corner of the entrance. So do not leave the turn too late.
- Close the lock at an angle that allows for the combined effect of current and wind. Plan where the set will take the ship before the bow reaches the entrance. Once the bow is in slack water inside the lock while the stern is still in the current, the ship will swing.
- If you are unsure about the current, the wind or how the ship will handle, use tugs and wait for better conditions.
Building lock-handling competence: the TMSA view
Lock entries are a skill that has to be learned. Tanker operators show how they build it through OCIMF's Tanker Management and Self Assessment (TMSA) programme, under Element 5: Navigational Safety. A university thesis that summarises Element 5 lists these good-practice KPIs:
| Stage | KPI | Best practice |
|---|---|---|
| 5.3.2 | Senior officers receive ship-handling training before promotion to Master or before joining a new vessel type | Ship-handling experience is gained through training within a competence development system |
| 5.3.3 | Navigational audits on passage by a suitably qualified and experienced company representative | Assess the bridge team's skills and how well the team works together, and identify further training needs |
| 5.4.3 | Competence assessment programmes ensure Masters and navigating officers maintain core and specialist skills | Assessments, which may be done in a simulator, include bridge team management behaviours |
| 5.4.4 | Navigating officers attend periodic refresher BRM (bridge resource management) simulator training | Training teams reflect the nationalities in the fleet and build awareness of cultural differences, communication style and hierarchy bias |
In practice, a lock or canal approach is a good thing to rehearse in a simulator before a first command or a new ship type. It is also a good moment for a riding audit to watch the pilot–master exchange, the thruster and engine orders, and how the forecastle team is briefed.
KPI numbers follow TMSA3 (OCIMF, in force since 2018), written as element.stage.KPI. OCIMF's SIRE 2.0 Universal Interpretations (2023) confirm 5.4.4 as the Bridge Team Management simulator KPI. The wording of the other three is summarised from a secondary source; the authoritative text is in the TMSA3 guide on the OCIMF/SIRE portal. Higher stages are progressively more demanding: Stage 3 and Stage 4 are best-practice levels beyond the Stage 1 baseline.
Self-test
- Why does high entry speed make stopping in the lock dangerous on a single-screw ship?
Answer 1
More speed needs more astern power to stop. Astern power makes the stern walk sideways and the ship swing, so the faster you enter, the harder you swing into the wall.
- Apart from the stopping problem, why must entry speed be minimal?
Answer 2
Displaced water must flow out between the hull and the walls. At higher speed this flow is faster, and if the ship is off the centreline the low pressure on the narrower side pulls her into the wall.
- Why stop the bow thruster early when correcting heading?
Answer 3
The bow keeps swinging after the thruster stops, so stopping late leads to overcorrecting.
- What happens if the forward spring is made fast while the ship still has headway?
Answer 4
The bow swings towards the side where the spring is held. Push it off with the bow thruster, and brief the forecastle team not to make the spring fast early.
- In a very narrow lock, what is the danger if the bow leaves the lead-in wall?
Answer 5
The bow shoulder may strike the far corner of the lock entrance.
- In a river lock, why should the turn not be left late?
Answer 6
The current keeps carrying the ship throughout the turn, towards the corner of the entrance.
References
- The lock authority's published regulations and lock dimensions for the waterway you are using.
- IMO Resolution A.960(23) on pilot training and pilot–master information exchange.
- Original lesson based on a Russian-language training presentation on lock-entry technique, reviewed but not reproduced.