Source, edition and limits
This original lesson is based on the supplied DNV-RU-SHIP, Part 3 Hull, Chapter 15 Stability, edition July 2024, issued by DNV AS, and separately linked IMO/MCA guidance. All 19 pages were reviewed. The supplied copy expressly prohibits further distribution, so the PDF, page images and original figures are not republished. The diagram below is original teaching material.
The chapter's changes page states that the July 2024 edition entered into force 1 January 2025, replacing July 2022, with editorial changes noted. This is an edition-specific study, reviewed 7 November 2026, not a claim that July 2024 is the latest or governing edition for every vessel. Use DNV's official Rules and Standards Explorer and the vessel's approved documents to establish applicable rules, amendments and class/flag requirements.
The chapter describes main-class stability requirements for vessels of relevant load-line length of 24 m and above, with applicability, service restrictions and additional notation provisions. Do not interpret that scope as exemption from all stability obligations for smaller vessels. Ship type, operation, flag rules and statutory instruments also matter.
Initial GM is not complete stability
KG is the centre of gravity above the keel; KM is the transverse metacentre above the keel. At small angles, GM = KM − KG, with the appropriate free-surface correction. GZ is the righting lever, which changes with heel. The righting moment is proportional to displacement weight × GZ.
No vessel data, scale or pass/fail result is represented. The initial slope relates to GM; the full curve and relevant limiting angles describe different parts of the assessment.
A positive GM does not guarantee adequate righting levers, area under the curve, downflooding margin or weather compliance. A higher GM is not automatically better in every operational respect: stiffness, acceleration, cargo/structure and other limits matter. Use the complete approved assessment rather than a single “safe GM.”
General intact criteria and conditional alternatives
The chapter's Section 1, 4.1.1 follows the general IMO 2008 IS Code criteria. As a short reference—not a complete compliance checklist—the general set includes:
| General criterion | Reference value in the reviewed text |
|---|---|
| GZ area from 0° to 30° | At least 0.055 m·rad |
| GZ area to 40°, or downflooding if earlier | At least 0.09 m·rad |
| GZ area from 30° to 40°, or downflooding if earlier | At least 0.03 m·rad |
| GZ at 30° heel or greater | At least 0.20 m |
| Heel angle of maximum GZ | Preferably above 30°; not below 25° in the general set |
| Initial GM | At least 0.15 m in the general set |
Angles in the area calculation are radians; plotting degrees without conversion does not give m·rad. Do not extrapolate a simple GM × sin(angle) approximation to create a compliant large-angle GZ curve. Apply the actual criteria and defined limiting angle from approved data; early downflooding can prevent satisfying them.
The chapter also has conditional alternatives, including timber deck cargo provisions and equivalent criteria in 4.1.3 where vessel characteristics make the general set impracticable. The equivalent set permits a maximum-GZ angle as low as 15° only with its own complete conditions and area requirements. Its variable first-area requirement for a peak between 15° and 30° is 0.055 + 0.001 × (30 − peak angle in degrees) m·rad; this gives 0.065 m·rad at a 20° peak. It does not let a reader simply replace 25° with 15° in the general table. Obtain the competent authority/class-approved basis for the vessel.
Downflooding and closure integrity
Downflooding is water entry through external openings into volumes treated as buoyant. The relevant downflooding angle concerns immersion of openings not protected by the appropriate closing arrangement under the applicable criteria. Its definition and treatment are more specific than “water reaches the deck edge.”
Openings, closing appliances, indicators, alarms and instructions are part of the evidence chain. A theoretical GZ curve cannot be relied on with unaccounted open doors, vents or other changes to buoyancy/closure assumptions. Do not assume an opening can be ignored merely because someone can close it later; follow approved closure and operating conditions.
Weather criterion: wind and rolling together
The chapter's weather assessment examines steady wind heel, rolling and gust-wind effects with the required comparison of heeling/righting areas. It is not just “GM above minimum,” nor is a diagram's wind heel an operational permission to sail in that weather.
The reviewed text requires free-surface effects in the relevant loading conditions. Its roll-assessment assumptions do not simply credit an operating anti-roll device as a permanent stability safeguard. Use the prescribed calculation method or an accepted alternative with appropriate evidence, not a generic roll-period shortcut. The lesson's conceptual GZ drawing is not a weather-criterion calculation.
Loading conditions and free surface
Assess the owner's intended service conditions and the applicable standard conditions, including departure/arrival, loaded/ballast and relevant deck-cargo cases. Fuel and stores consumption can change the critical condition; passing departure does not establish arrival or every intermediate stage.
Both initial stability and the stability curves need the appropriate free-surface treatment. For an introductory initial-GM correction, FSC = sum of tank FSM ÷ displacement, using consistent mass units. This does not replace the approved large-angle free-surface method. Actual tank geometry and filling matter; weight × KG is a loading moment, not a free-surface moment.
Deck-cargo weight, height, realistic stowage, water absorption/icing where applicable and any claimed cargo buoyancy must follow the governing assumptions. The chapter's standard calculation cases are not instructions to empty ballast tanks or load the summer mark in every operation. Use the Part 2 worked stability examples as arithmetic revision, not loading authorisation.
Intact and damage stability are separate
Intact criteria concern the specified undamaged condition. Damage stability considers applicable flooding/damage cases and their consequences. Chapter 15 directs readers to additional rule chapters for relevant class notations and ship types; statutory damage requirements may also apply.
A dash or “no IMO requirements” note in an individual notation table is not a blanket exemption from every class, statutory or vessel-specific damage-stability requirement. Check all applicable rules and the approved damage documentation, not one cross-reference row. The general GZ values above do not substitute for damage assessment.
Lightweight data and approval evidence
Lightweight displacement and centre of gravity underpin the calculations. The chapter requires appropriate determination of lightweight data, with inclining tests or, where an authorised dispensation applies, lightweight survey/sister-ship evidence. Exemptions are conditional—not automatic because two ships look alike.
Tests/surveys use an approved procedure with the required class involvement, and the report needs the appropriate signature and endorsement. This lesson is not an inclining-test tutorial. Modifications, permanent equipment and ballast changes must be handled through the applicable lightweight-change and approval process.
The ship needs approved stability information enabling the Master to assess varying service conditions. Loading-computer approval is separately governed; installing a computer does not prove correct lightship data, tank inputs, cargo data or operating assumptions. Verify approved version, applicable limits and the condition actually entered.
Practical evidence review
- Identify the applicable rule edition, flag basis, class notations and operation-specific criteria.
- Check approved stability booklet, hydrostatics, lightweight definition/data and loading-instrument documentation.
- Confirm actual weights, centres, tank quantities/free surfaces, draft/trim and closure assumptions.
- Review the complete relevant intact/weather/damage results and operational limits—not just green GM.
- Refer discrepancies, changed equipment or unapproved conditions for competent assessment; do not compensate by improvised ballast or data changes.
Self-test — 8 Questions
- Does positive GM alone establish full intact-stability compliance?
Answer 1
No. Check the full applicable GZ curve, area criteria, limiting angles, free surfaces, weather assessment and operating conditions. GM is only initial stability.
- What peak-angle criterion belongs to the reviewed general set, and can 15° be substituted freely?
Answer 2
The general set prefers a peak above 30° and requires at least 25°. The conditional equivalent criteria may permit 15° with their complete additional conditions; they are not a universal replacement.
- Under the reviewed equivalent formula, what first-area value corresponds to a 20° peak?
Answer 3
0.055 + 0.001 × (30 − 20) = 0.065 m·rad. This applies only within that equivalent set and does not establish complete compliance by itself.
- Is deck-edge immersion always the downflooding angle?
Answer 4
No. Relevant external openings and approved closing/buoyancy assumptions determine downflooding under the applicable criteria; deck edge alone is not the definition.
- Does passing the departure condition prove every voyage condition is acceptable?
Answer 5
No. Arrival, ballast, intermediate and operation-specific cases can be critical as fuel, stores, cargo and free surfaces change.
- Is free-surface treatment required only for initial GM?
Answer 6
No. The reviewed chapter requires correction of initial metacentric height and stability curves. Use the approved treatment for the actual tanks and large-angle assessment.
- Do the general intact GZ criteria replace damage-stability requirements?
Answer 7
No. Damage stability has separate applicable cases/rules, including statutory and class/notation provisions. Check the vessel's full approved basis.
- Does a loading computer or sister ship automatically validate lightweight data?
Answer 8
No. Lightweight determination, any dispensation and survey/test evidence require the applicable approval process; computer approval and actual input accuracy are separate checks.
Sources and further reading
- Primary reviewed source: DNV AS, DNV-RU-SHIP Pt.3 Ch.15, Stability, July 2024, Section 1 (scope/documentation; general, equivalent and weather criteria; loading assumptions; damage cross-references; lightweight determination). Restricted uploaded copy not redistributed.
- DNV Rules and Standards Explorer and DNV rules/standards: obtain the authorised applicable edition and linked chapters/guidelines, including stability documentation and loading instruments.
- IMO 2008 Intact Stability Code, MSC.267(85): general criteria, weather assessment and ship-type provisions; read with applicable amendments.
- MCA MSIS 43 Intact Stability guidance: Code and surveyor guidance; UK scope does not automatically establish another flag's requirements.
- MCA approval of vessel stability information: approval and evidence context.