Source and scope

This original companion uses the uploaded “Master & Mates Examination — Part 2: Navigation, Stability, Safety & H₂S” as a revision checklist. Its filename refers to ARAMCO, but official endorsement, author and date are unverified. It is not official Aramco training. Even answers labelled “Corrected / verify” need further qualification. The document is not reproduced or redistributed.

Read Part 1: lights, signals and buoyage alongside this lesson. Official references below were reviewed 7 November 2026. This is not loading approval, a passage plan, gas-entry instruction or an emergency procedure. Approved vessel data, current navigational products, flag rules and the safety management system take precedence.

Stability and clearance: separate checks

Original diagram comparing slack-tank free surface with under-keel clearance, showing corrected GM and depth calculations.

Neither check replaces the other, and neither sketch authorises an operation.

KG, GM and loading

Δ is displacement (t); KG is the centre of gravity above the keel (m); KM is the transverse metacentre above the keel (m). GM = KM − KG before free-surface correction. GZ is the righting lever; at small angles, GZ ≈ GM × sin(heel). Positive GM alone does not establish full stability compliance: the righting-arm curve, downflooding, strength and operating restrictions also matter. Negative initial GM is dangerous and can produce an angle of loll; do not apply an improvised ballast correction.

New KG = total vertical loading moment ÷ new displacement.

ItemMassKGVertical moment
Vessel1000 t4.00 m4000 t·m
Added load200 t5.00 m1000 t·m
Total1200 t4.1667 m5000 t·m

The load is 200 tonnes, not 200 kilograms. KG rises about 0.167 m. GM would decrease by that amount only if KM stayed unchanged; obtain new-condition KM from approved hydrostatics. A 20% displacement increase is not automatically negligible. Loading above G raises KG; below G lowers it, but actual stability also depends on hydrostatics, free surface and trim. Verify tank contents and records at vessel-required intervals, not an invented universal daily sounding rule.

Free surface: not always worst at half filling

Liquid shifts towards the low side in a slack tank. Its effect on initial stability is a virtual rise of G.

FSC (m) = sum of FSM (t·m) ÷ displacement (t). Corrected GM = KM − KG − FSC.

For a rectangular free surface of length l and transverse breadth b, I = l × b³/12 and FSM = liquid density × I in the small-angle idealisation. With an unchanged rectangular footprint, this moment is not uniquely greatest at 50% filling. Real geometry, level and heel matter: use approved tank tables or the approved loading-computer method. Manage slack tanks and cross-connections under vessel procedures; do not assume a “full” tank necessarily has no residual free surface without checking its condition.

Worked condition: 800 t at KG 4.6 m; loads 150 t at 3.5 m, 220 t at 4.0 m, 80 t at 4.8 m and ballast 50 t at 1.5 m. Δ = 1300 t; moment = 5544 t·m; KG = 4.2646 m. With supplied KM 6.6 m, uncorrected GM = 2.3354 m. The ballast tank's FSM is missing, so corrected GM is undetermined. The product 50 × 1.5 = 75 t·m is a vertical loading moment, not FSM. Only if an independent tank-table FSM were 75 t·m would FSC be 0.05769 m and corrected GM approximately 2.2777 m.

TPC, density and freshwater allowance

TPC is tonnes per centimetre immersion, for a stated condition/density. For small changes with approximately constant hydrostatics, sinkage (cm) ≈ mass added ÷ TPC.

Approximate FWA (mm) = Δ/(4 × TPC), with seawater TPC at the applicable load-line condition and reference densities 1.025/1.000 t/m³. Dock-water allowance = FWA × (1025 − density in kg/m³)/25. Use the certified FWA where applicable and keep units consistent.

ExampleWorkingResult
Add 56 t; TPC 12 t/cm56/124.6667 cm sinkage
900 t at KG 4.1 m; load 120 t at 5.0 m(3690+600)/1020KG 4.2059 m
Δ 1700 t; seawater TPC 9 t/cm1700/(4×9)FWA 47.22 mm
Δ 1580 t; TPC 11; density 1025 → 1005 kg/m³FWA 35.91 mm ×20/25Sinkage 28.73 mm; 3.2 m → about 3.2287 m
FWA explicitly 20 cm; seawater draft 3.2 mAdd 0.20 mFreshwater draft 3.40 m at unchanged displacement

The sheet's rig-move masses total 1900 t. A 50 cm rise at an assumed constant TPC of 10.5 suggests 525 t discharge arithmetically—not a discharge plan. Large changes require hydrostatics, trim, strength, stability, safe sequencing and reserves.

Load-line labels: TF tropical fresh; F fresh; T tropical; S summer; W winter; WNA winter North Atlantic. Assigning-authority initials are not seasonal marks. Apply the certificate, applicable zone/season and Convention provisions, not an assumed Gulf rule.

Deck loading: arithmetic is not approval

48 t over a 4 × 3 m plan area averages 4.0 t/m². Below an assumed uniform limit of 4.5 t/m², this passes the arithmetic screen only. Feet/skids concentrate loading: check actual support/bearing areas, local and global structure, approved spreading arrangements, dynamics, securing, lifting and stability.

80 t over 16 m² averages 5.0 t/m², exceeding an assumed 4.8 t/m² limit. Do not improvise extra footprint; any engineered spreading/support arrangement must be approved for the actual structure.

Under-keel clearance, tide and squat

Static UKC = chart depth + tide above the same datum − relevant draft. Check trim, deepest hull/appendage, sounding quality, water-level uncertainty and transducer reference; then account for squat, heel, wave motion and applicable minimum margins.

3.7 m chart depth +1.6 m same-datum tide −3.2 m draft = 2.1 m static UKC. If a separately verified obstruction top is 1 m above that seabed and not already included in charted least depth, static clearance is 1.1 m. Do not subtract an obstruction twice. Neither number alone approves or prohibits pipeline crossing: least depth, restrictions and operator rules remain necessary. The sheet does not verify a current Aramco UKC limit.

A sounder showing 12 m below the keel, with 3.5 m keel draft, implies 15.5 m total water depth ≈ 50.85 ft (50.9 ft rounded). A below-transducer or surface-corrected display needs a different calculation: verify offsets first.

Squat is speed-related sinkage and trim change, aggravated by shallow/restricted water. Cb × V²/100 and doubled confined-water expressions are empirical estimates with applicability limits—not universal clearance predictions. Use the vessel/port-approved method and its speed-through-water assumptions; reduce speed as required while maintaining control. No single depth/draft ratio defines when squat suddenly begins.

Compass, celestial bearings and current

Use east-positive/west-negative signed errors: true = compass + deviation + variation, normalised through 360°. Deviation is vessel/heading dependent; variation depends on location/date. Gyro error is separate, not magnetic variation plus deviation.

  • Compass 243°, variation 3° W, deviation 2° E → 242° true.
  • Compass 245°, variation 2.5° W, deviation 1.5° W → 241° true.
  • A hypothetical rose 3°30′ W in 2005 decreasing 6′ annually gives 1°24′ W in 2026. Current charts/geomagnetic information take precedence over indefinite extrapolation.

GHA is an angle, westward from Greenwich to the body's hour circle, not an hour reading. Declination is north/south of the celestial equator. LHA = GHA + east longitude − west longitude, normalised through 360°. For a Sun compass check, record accurate UTC/position and properly observed compass bearing, use the date's almanac and the chosen azimuth tables' naming rules, then compare true azimuth with the observed bearing. Never look directly at the Sun without appropriate observation equipment.

A berth label is not necessarily the ship's exact true heading. Use a verified transit or suitable observation rather than assuming berth alignment equals heading. Wrap true-minus-compass error to the sensible signed difference.

Set is towards; drift is speed. Ground velocity = water-track velocity + current velocity. Wanted track 105° true; current 085° at 2 kn; water speed 10 kn; no leeway: cross-current = 2 sin20° = 0.684 kn. Correction = arcsin(0.684/10) ≈3.92°; steer 108.92° true, SOG ≈ 11.92 kn. Monitor changes. A 15° track error alone does not establish “steer 190°”: heading, speed, current and leeway are needed.

Radar and watchkeeping

Check EBL/VRM reference, heading/speed inputs, orientation and clutter. North-up may aid chart comparison but is not a universal mandatory mode. CPA/TCPA estimates depend on valid inputs and tracked motion; maintain visual lookout, systematic radar observation and independent position checks.

Fix frequency depends on hazards, speed, uncertainty and reaction time. Neither 30 minutes nor 3–6 minutes is a universal confined-water rule. Continuous monitoring, suitable independent fixes and parallel indexing help detect errors. Watch composition follows STCW, traffic, visibility, workload and vessel procedures.

Backing wind changes anticlockwise; veering changes clockwise. 1.0–1.5 m significant wave height is not universal permission for work beside a platform: operation-specific limits include motion, wave period/direction, clearance, transfer method and abort arrangements. Verify current vessel/operator limits.

Person overboard and recovery

Raise the alarm, deploy suitable flotation/marking if safe, maintain a dedicated visual reference, mark time/position, inform the Master and mobilise the recovery plan and assistance. A GPS MOB mark does not follow casualty drift.

The Williamson turn is a recognised return-track manoeuvre, often taught with opposite rudder about 60° from original heading and easing about 20° before the reciprocal. These are training cues, not guaranteed vessel performance. Turn selection, helm, propulsion and speed depend on manoeuvring characteristics, obstacles and casualty location; do not automatically start a bow thruster or prescribe constant speed.

There is no universal weather-side recovery. Follow the ship-specific recovery plan, assessing sea, wind, freeboard, machinery hazards and casualty condition. An exhausted/unconscious person may not climb a net; use suitable tested recovery equipment and trained personnel. Seek medical advice and handle cold-water casualties carefully. Plan recovery rather than improvising propulsion near the casualty.

Distress, alarms and life-saving equipment

VHF Channel 16 (156.8 MHz) is voice distress; Channel 70 is DSC, not voice. MF examples: 2182 kHz voice, 2187.5 kHz DSC. Use fitted GMDSS equipment and trained procedures for the sea area. MAYDAY identifies vessel, position, distress and assistance needed. Recognised Annex IV signals are not casual exercise signals; do not demonstrate signalling by making a fire.

The general emergency alarm is seven or more short blasts followed by one long blast, with the prescribed shipboard alarm arrangements. Follow muster-list actions; it is not an abandon-ship order. Learn vessel-specific fire, gas and MOB signals rather than assuming universal three-blast codes.

Check survival-craft capacity against approved records, not a blanket “100% on each side.” Inspect servicing, HRU validity, painter, weak link and lashings against the manufacturer's approved arrangement. Not every HRU has a two-year life. Never improvise release-gear tests or alter float-free arrangements. Rescue-boat launch/release requires trained personnel and the specific equipment instructions. An EEBD is escape-only, not entry, firefighting or rescue.

H₂S: prevent a second casualty

Hydrogen sulphide is toxic and flammable. Never use smell to establish safety: olfactory fatigue and exposure can remove the warning. Use appropriately located approved gas detection, required checks and training. Exposure limits vary by jurisdiction/purpose; this lesson does not prescribe entry limits or alarm thresholds.

Raise the alarm and follow coordinated vessel/installation emergency plans. Move by a safe route to the designated safe place, using specified escape protection if trained/required. Wind direction does not prove accommodation, bridge or escape route is safe. Shelter/ventilation, ignition control, propulsion, mooring release and escape decisions require the actual plan and situation—not automatic casting off, starting engines or generic spray instructions. Water spray does not establish breathable air or permission to approach a release.

Do not rush into contaminated air to rescue someone. Activate planned rescue and medical help. Rescue requires trained responders, suitable positive-pressure breathing apparatus, assessed controls, support and rescue arrangements; SCBA alone does not authorise entry. An EEBD is not a rescue substitute. First aid/CPR belongs in safe air after safe recovery, following training and medical advice. Re-entry requires authorised assessment/testing—not smell or a casual “all clear.”

Self-test — 12 Questions

  1. What is new KG for 1000 t at 4.0 m plus 200 t at 5.0 m? Is new GM known?

Answer 1

KG = 5000/1200 = 4.1667 m. New GM needs applicable KM and free-surface correction.

  1. Is rectangular-tank free surface uniquely greatest at half filling?

Answer 2

No. An unchanged rectangular footprint has the same idealised small-angle moment at different slack levels; use actual approved tank data.

  1. Is 50 t × KG 1.5 m a free-surface moment?

Answer 3

No. 75 t·m is a vertical loading moment; FSM needs separate tank data. Corrected GM cannot be fixed from that product.

  1. Find sinkage for 56 t added at constant TPC 12 t/cm.

Answer 4

4.6667 cm, approximately 4.7 cm deeper; the approximation excludes significant hydrostatic/trim changes.

  1. Find FWA for Δ1700 t and seawater TPC 9 t/cm.

Answer 5

47.22 mm, from 1700/(4×9). Use certified FWA where applicable.

  1. Does 4.0 t/m² averaged below a 4.5 t/m² deck limit approve loading?

Answer 6

No: arithmetic screen only. Verify actual supports, local/global strength, approved spreading, dynamics, securing and stability.

  1. Depth 3.7 m, same-datum tide +1.6 m, draft 3.2 m: what does UKC establish?

Answer 7

2.1 m static UKC, not passage approval. Apply dynamic effects, uncertainty, obstructions, restrictions and minimum margins.

  1. Compass 243°, variation 3° W, deviation 2° E: true bearing?

Answer 8

Error −3+2 = −1°; 242° true.

  1. Track 105°, current 085°/2 kn, water speed 10 kn, no leeway: course and SOG?

Answer 9

Approximately 108.92° true and 11.92 kn; monitor actual conditions rather than reuse this example blindly.

  1. Does the general emergency alarm order abandonment?

Answer 10

No. Seven or more short blasts and one long blast initiate muster-list actions. Abandonment is a separate command under procedures and Master's authority.

  1. Must MOB recovery be on the weather side or by climbing a net?

Answer 11

No. Use the vessel-specific recovery plan and suitable method for conditions/casualty; an incapacitated person may not climb. Control machinery hazards.

  1. Can smell, an EEBD or simply wearing SCBA authorise H₂S rescue entry?

Answer 12

No. Never rely on smell or attempt unprotected rescue. EEBD is escape-only; activate trained, planned rescue with appropriate breathing apparatus, assessed controls and support. SCBA alone is not entry authorisation.

Official references and further study

Related lessons

Continue to Part 3

Anchor Handling, Equipment & Conversions — Examination Part 3 covers tow load paths, equipment verification, rig-move readiness and checked unit conversions.

Stability rules companion

Ship Stability — GZ Curves, Weather Criteria & Lightweight Data explains the full stability assessment behind these arithmetic examples.